How To Make LSD Gel Tabs
If you're curious about the process of making LSD gel tabs, you've come to the right place. In this comprehensive guide, we'll take you through everything you need to know about creating your own LSD gel tablets, from start to finish. Whether you're interested in creating these psychedelic substances for personal use or for research purposes, we've got you covered. Our step-by-step instructions will walk you through the process, so you can make high-quality, potent LSD gel tabs that are sure to impress. So, let's dive in and discover how to make LSD gel tabs today!
Make LSD Gel Tabs: Step-By-Step Guide
However, if you have been wondering how to make LSD Gel tabs then this guide would suffice. This is a TEK for alaying a 100 count mold (usually squares) of LSD Gel Tabs.
Requirements
- 11 mg LSD Crystal (We weigh 10% over the stated dosage because some wastage of solution is inevitable when pouring the gels)
- 5 ml Distilled H2O
- 3.75g gelatin (Although this can be reduced down to 3.5g once your pouring technique improves)
- 5 ml Glycerin (Kosher, Food Grade)
- Food Coloring (1 drop per 100 gel tabs)
- Mold (PLA or PLA+ 3D printed)
- Overhead Stirrer
- Heating Element / Hot Plate (For best results use a mag stirrer that also doubles up as a heating element)
- Thermometer
- Plastic Popsicle Sticks (For stirring the solution)
- Small Metal Spatula (For weighing)
- 2 x 50ml Borosilicate Beakers (Heat resistant)
It is important to weigh/measure everything before you start, because once you start the process you will not have time to stop and do something you forgot.
Stay updated with the
You must be registered for see links
on
You must be registered for see links
. Visit
You must be registered for see links
. The Procedure
Step 1
Once you have everything set up, weighed and measured, put your 5 ml of glycerine in one of the borosilicate beakers.
Step 2
Then add your 11 mg of LSD crystal and 1 drop of food coloring and mix thoroughly using the overhead stirrer. Set the speed as high as possible without it causing air bubbles to appear in the solution.
Step 3
Next, slowly add the gelatine to the solution, in very small amounts at a time. Make sure it is completely mixed. No granules at all should be showing.
Step 4
When you have all the gelatine mixed into the solution, begin heating your distilled water up to a temperature of 80 degrees F (27 degrees C).
Step 5
As soon as the distilled water hits 80 degrees F, pull it off the heater and pour it in your gelatine mixture.
MIX QUICKLY AND THOROUGHLY (YOU ONLY HAVE ABOUT 10 SECONDS BEFORE IT BEGINS TO HARDEN)
The solution will be very viscous to begin with, and the more you stir the thinner it will become until it is ready to pour.
Step 6
As soon as the solution is all mixed and the consistency is thin enough, pour the solution into your mold.
Make sure it is on as flat a surface as possible while pouring. You may have to physically grab the mold and rotate it to work the solution into all the gel tabs.
The process of pouring is the hardest part. You have to be very quick and accurate to get it to pour evenly into the mold before it hardens.
Step 7
After you have filled the mold, let it air dry overnight, with the assistance of a fan if one is available.
Step 8
In the morning, pop the gels out of the mold. You will have to go around the edges with a knife or toothpick to free the gels from the mold, and once they are unstuck you can slowly peel them off in one big piece.
Done. Now you know how to make LSD Gel tabs. Enjoy your gels with family and friends!
Resource:
You must be registered for see links
You must be registered for see links
You must be registered for see links
You must be registered for see links
Disclaimer: Read the complete disclaimer
You must be registered for see links
.